0

O-rings

Is coolant seeping from the thermostat housing, or does an AN fitting in the fuel system need to seal again? An O-ring is a small rubber ring that seals between two parts. Here you can choose between individual O-rings and complete kits for the engine, fuel system and front fork, both for repairs and for your project.

What O-rings seal – from thermostat to AN fittings

An O-ring sits in a groove and is compressed when the parts are assembled, sealing against coolant, oil, fuel or air. The range includes, for example, thermostat O-rings and an O-ring kit for fuel injectors from MAHLE Original, a throttle body O-ring from FAST and O-rings for AN fittings from Fragola and Radium Engineering. There are also O-rings for the front fork compression piston from KYB and a diaphragm and O-ring kit for fuel pressure regulators from Fuelab. Individual parts are found under O-rings, while O-ring kits combine several sizes or all the rings for one component.

How to choose the right O-ring

Several factors must match before the ring seals reliably:

  • Size: Inner diameter and cross-section must match the groove. A ring that is too thin can leak, and one that is too thick can get pinched.
  • Material: NBR (nitrile rubber) is typically used for oil and fuel, but suitability depends on the fluid and temperature.
  • Hardness: Specified in Shore, e.g. 70 for Athena's NBR O-ring. The choice depends on pressure and the surface finish.
  • Fitting type: For AN fittings, the ring must match both the AN size and the thread, e.g. -8AN with 3/4-16.

Installation and maintenance

Clean the groove and the contact surface, and lightly lubricate the O-ring with a product compatible with the material and the fluid so it doesn't twist or get cut during assembly. Guide it carefully past sharp edges and threads. If you also need to replace gaskets, you can find them under engine gaskets and seals and in the rest of gaskets and seals. Brands in the category include, for example, Victor Reinz, Fel-Pro, Cometic Gasket, S&S Cycle and Athena.

Frequently asked questions

Can I reuse an O-ring?

It is typically not recommended. After use, the ring is often flattened and can be hardened or cracked by heat and fluids, so it seals less effectively. Replace it every time the joint is taken apart.

Should I choose individual O-rings or an O-ring kit?

Individual O-rings are a good fit when you know the exact size. A kit is practical for e.g. fuel injectors or a fuel pressure regulator, where several rings are replaced at the same time, or when your project has several AN sizes.

Why does a new O-ring leak?

Typical causes are the wrong size, a material that doesn't tolerate the fluid, a ring that was twisted or cut during installation, or a scratched or dirty groove. Check the size and material for the specific part number.

How do I measure an O-ring?

Measure the inner diameter and the cross-section with a caliper. A used ring may be stretched or flattened, so compare with the groove dimensions or the manufacturer's dimensions for the component the ring sits in.

View as Grid List
Sort by
Display per page

6-10AN VTN ORING PK

rad18-0043
Radium Engineering O-Ring Multi Pack 6AN/8AN/10AN
$152.78 excl. VAT

FUELAB Diaphragm Kit

flb14602
Fuelab Diaphragm & O-Ring Kit for 515xx/525xx Series Regulators - Large Seat
$282.74 excl. VAT

LSXR/RT Throttle Body O-Ring

fst146004
FAST O-Ring Seal For 102MM Throttle
$160.15 excl. VAT

O-Ring - 11028

nex11028
Nitrous Express 1-1/8 O-Ring (Fits 5lb/10lb/12lb/15lb Bottle Valve)
$65.48 excl. VAT

RUBBER GASKET

vib12575G
Vibrant Replacement O-Ring for 2.50in HD Weld Fittings
$93.60 excl. VAT

RUBBER GASKET

vib12546R
Vibrant Replacement O-Ring for 3in Weld Fittings (Part #12546)
$118.04 excl. VAT

RUBBER GASKET

vib12548R
Vibrant Replacement O-Ring for 4in Weld Fittings (Part #12548)
$134.17 excl. VAT

RUBBER GASKET

vib12577G
Vibrant Replacement O-Ring for 3.50in HD Weld Fittings
$93.73 excl. VAT

RUBBER GASKET

vib12580G
Vibrant Replacement O-Ring for 5.00in HD Weld Fittings
$103.57 excl. VAT

RUBBER GASKET

vib12547R
Vibrant Replacement O-Ring for 3.5in Weld Fittings (Part #12547)
$134.24 excl. VAT

RUBBER GASKET

vib12576G
Vibrant Replacement O-Ring for 3.00in HD Weld Fittings
$93.67 excl. VAT