0

V-Band Clamps

Need to be able to separate your turbo, wastegate or exhaust without unbolting an entire multi-bolt flange? V-band clamps join two flanges with a single tightening bolt and are for you if you are working on a turbo project or an exhaust with V-band flanges.

What a V-band clamp does

A V-band clamp is a band with a V-shaped profile that pulls two flanges together when you tighten the nut. The joint is typically used between the turbo and the exhaust, on the wastegate and on the blow-off valve. In this category you will find, for example, the Turbosmart BOV V-Band Clamp Assembly and a TiAL Sport MVS kit for the wastegate inlet and outlet. Other types of joints can be found under clamps and hose clamps.

How to choose the right clamp

The clamp must fit the flanges, not just the pipe diameter. In particular, check:

  • Flange outer diameter – for example, Vibrant lists clamps for flanges with a 1.5 or 3.85 inch outer diameter.
  • Profile and flange type – some clamps are made for specific flanges, such as Vibrant's models for the inlet and outlet flange on a TiAL housing for GT28/GT30/GT35.
  • Closure – quick release models are made for fast removal and installation. Choose based on how often the joint needs to be separated and how good the access is.
  • Material and location – close to the exhaust manifold and turbo, the demands on heat resistance are typically higher than further back, for example with stainless steel clamps such as the Mishimoto Stainless Steel V-Band Clamp.

Installation and maintenance

Clean the flanges and check that they are aligned before fitting the clamp – a misaligned joint can cause leaks. Tighten evenly according to the manufacturer's instructions, and typically retighten after the first heat cycles, as the joint can settle. A deformed band or worn thread should be replaced rather than reused. Brands in this category include Garrett, Ticon and TiALSport.

Frequently asked questions

Does a V-band joint need a gasket?

It depends on the flanges. Many V-band flanges are designed to seal metal to metal, while others have room for a gasket or O-ring. Follow the instructions for the specific flange kit and clamp.

Can I reuse a V-band clamp?

Often yes, if the band is not deformed and the thread and nut are in good condition. If the band is stretched or cracked, or the joint has leaked, it is typically better to replace it so the joint can be tightened correctly.

How do I find the right size?

Measure the flange's outer diameter and compare it with the product description – not just the pipe diameter. For a wastegate, blow-off valve or turbo housing, you may need a clamp that matches that exact flange, such as a specific flange number.

View as Grid List
Sort by
Display per page

Blow Off Valve - TS-0203-1008

turTS-0205-3009
Turbosmart BOV V-Band Clamp Assembly
$409.08 excl. VAT

Mishimoto MMCLAMP-VS-3

misMMCLAMP-VS-3
Mishimoto Stainless Steel V-Band Clamp - 3in
$446.77 excl. VAT

S.S. V-BAND CLAMP

vib1486C
Vibrant SS Quick Release V-Band Clamp for V-Band Flanges with 1.5in O.D.
$293.52 excl. VAT

S.S. V-BAND CLAMP

vib1415C
Vibrant SS V-Band Clamp for outlet flange on Tial Housing for GT28/GT30/GT35 (Matches Flange #1415)
$315.88 excl. VAT

S.S. V-BAND CLAMP

vib1491C
Vibrant SS Quick Release V-Band Clamp for V-Band Flanges with 3.85in O.D.
$304.16 excl. VAT

S.S. V-BAND CLAMP

vib1416C
Vibrant SS V-Band Clamp for Inlet flange on Tial Housing for GT28/GT30/GT35 (Matches Flange #1416)
$315.28 excl. VAT