0

Spacers & Shims

Do you need a precise spacer between the pinion bearings, or does a rod end need to work at a greater angle? This category contains spacers for differentials, axles and wipers as well as spacers for rod ends, so you can get bearing preload, geometry and fitment to work out.

Spacers for differentials and axles

A pinion spacer sits between the pinion bearings and helps determine the bearing preload. A crush spacer – a spacer that is compressed when the pinion nut is tightened – deforms during installation, which is why it is typically recommended to use a new one whenever the differential is taken apart. At OMIX you will find, for example, pinion spacers for Dana 44, Dana 35 and AMC 20 as well as a crush spacer for Jeep Liberty and Wrangler. There is also a conversion spacer for the AMC 20 axle and a spacer for the wiper pivot on Jeep CJ. Pinion depth and gear mesh are typically adjusted with shims, so check whether your project requires them too.

How to choose a rod end spacer

At QA1 you will find high misalignment spacers in stainless steel. They sit on each side of the ball in a rod end and give the joint room to work at a greater angle without hitting the bracket. Choose based on several dimensions at once:

  • Inside diameter, which must match the bolt diameter.
  • Ball width – narrow and standard ball width are not the same.
  • Overall width relative to the opening in the bracket.
  • Material relative to the environment the part will be used in.

Dimensions are given in inches, so measure your existing parts before you choose.

Installation and accessories

Use the bolt, nut and tightening torque specified by the vehicle or component manufacturer, and check that the spacer sits flat without play. You will find suitable bolts in the sister category, and under spacers the individual spacers are gathered in one place.

Frequently asked questions

Can I reuse a pinion crush spacer?

It is typically not recommended. A crush spacer deforms when the pinion nut is tightened and cannot provide the same bearing preload again afterwards. As a rule, use a new one whenever the pinion is removed.

What is the difference between narrow and standard ball width?

It describes the width of the ball in the rod end the spacer will be fitted to. The spacer must match exactly that ball width and the bolt diameter, otherwise the joint can develop play or sit crooked.

How do I know if a pinion spacer fits my axle?

It depends on the axle type, not just the car. Check whether you have, for example, a Dana 35, Dana 44 or AMC 20, and compare with the product description for the specific part number.

Do rod ends with spacers need approval for inspection?

It depends on the product, the car and where the part is fitted. Modifications to steering or suspension may require approval, so check the specific part number and ask your inspection centre before you install.

View as Grid List
Sort by
Display per page

QA1 Misalignment Spacer

qapSN20-1211-H
QA1 Narrow Ball Width High Misalignment Spacer - 1.25in OD x .75in ID x 2.625in Wide - S.S.
$258.77 excl. VAT

QA1 Misalignment Spacer

qapSG10-84
QA1 Standard Ball Width High Misalignment Spacer - .5in ID x 1.25in Wide - Stainless Steel
$155.46 excl. VAT

QA1 Misalignment Spacer

qapSN12-88
QA1 Narrow Ball Width High Misalignment Spacer - .75in OD x .5in ID x 1.75in Wide - Stainless Steel
$150.44 excl. VAT

QA1 Misalignment Spacer

qapSG12-108
QA1 Standard Ball Width High Misalignment Spacer - .75in OD x .625in ID x 1.875in Wide - S.S.
$155.53 excl. VAT

QA1 Misalignment Spacer

qapSN16-913
QA1 Narrow Ball Width High Misalignment Spacer - 1in OD x .563in ID x 2.625in Wide - Stainless Steel
$242.37 excl. VAT

QA1 Misalignment Spacer

qapSG12-88
QA1 Standard Ball Width High Misalignment Spacer - .75in OD x .5in ID x 1.875in Wide - S.S.
$155.53 excl. VAT

QA1 Misalignment Spacer

qapSG14-1012
QA1 Standard Ball Width High Misalignment Spacer - .875in OD x .625in ID x 2.425in Wide - S.S.
$206.08 excl. VAT

QA1 Misalignment Spacer

qapSN16-1218-H
QA1 Narrow Ball Width High Misalignment Spacer - 1in OD x .75in ID x 3.25in Wide - Stainless Steel
$280.46 excl. VAT

QA1 Misalignment Spacer

qapSG16-1210
QA1 Standard Ball Width High Misalignment Spacer - 1in OD x .75in ID x 2.625in Wide - S.S.
$150.98 excl. VAT

QA1 Misalignment Spacer

qapSG14-813
QA1 Standard Ball Width High Misalignment Spacer - .875in OD x .5in ID x 2.5in Wide - S.S.
$150.51 excl. VAT

QA1 Misalignment Spacer

qapSG12-84
QA1 Standard Ball Width High Misalignment Spacer - .5in ID x 1.375in Wide - Stainless Steel
$155.53 excl. VAT

QA1 Misalignment Spacer

qapSN6-45
QA1 Narrow Ball Width High Misalignment Spacer - .25in ID x 1in Wide - Stainless Steel
$150.37 excl. VAT

QA1 Misalignment Spacer

qapSN8-68
QA1 Narrow Ball Width High Misalignment Spacer - .5in OD x .375in ID x 1.5in Wide - Stainless Steel
$156.94 excl. VAT

QA1 Misalignment Spacer

qapSN24-1221-H
QA1 Narrow Ball Width High Misalignment Spacer - 1.5in OD x .75in ID x 4in Wide - Stainless Steel
$261.38 excl. VAT

QA1 Misalignment Spacer

qapSG16-1212
QA1 Standard Ball Width High Misalignment Spacer - 1in OD x .75in ID x 2.875in Wide - S.S.
$156.07 excl. VAT

QA1 Misalignment Spacer

qapSN12-107
QA1 Narrow Ball Width High Misalignment Spacer - .75in OD x .625in ID x 1.625in Wide - S.S.
$150.44 excl. VAT

QA1 Misalignment Spacer

qapSN14-99
QA1 Narrow Ball Width High Misalignment Spacer - .875in OD x .563in ID x 2in Wide - Stainless Steel
$150.51 excl. VAT

QA1 Misalignment Spacer

qapSN14-89
QA1 Narrow Ball Width High Misalignment Spacer - .875in OD x .5in ID x 2in Wide - Stainless Steel
$150.51 excl. VAT