0

Water Methanol Nozzles

How much fluid should go into the intake, and how should the nozzle be positioned to give even atomisation? This category brings together nozzles and nozzle holders for water methanol injection – for you who want to adapt, expand or maintain an existing system.

The nozzle's role in the system

The nozzle atomises the water methanol mixture into a fine mist in the intake, where it can lower the air temperature and thereby counteract knock. How much is injected is controlled by the pump and a water methanol controller, but the nozzle size sets the limits for the flow. Nozzles from Snow Performance are available in several sizes, e.g. 0.5 GPH and 0.75 GPH, as well as part numbers such as SNO-N0050, SNO-N1600 and SNO-N2000.

How to choose nozzle and holder

  • Flow requirement: The right size depends on engine power, boost pressure and the ratio between water methanol and fuel. Too much fluid can cause poorer combustion, too little gives less cooling effect.
  • Number of nozzles: For larger requirements, the flow can be split between two smaller nozzles, which can give better atomisation than one large one.
  • Connection: The nozzle is typically screwed into a holder with a 1/8-inch NPT thread. Holders are available with push-to-connect fittings for 1/4-inch tubing, with a 4AN connection, as a straight low-profile version and with a 90-degree angle.
  • Placement: Distance to the throttle body and placement before or after the intercooler affect distribution – follow the instructions for your system.

Installation and maintenance

The nozzle typically points with the airflow, and the thread is sealed according to the manufacturer's instructions. Over time, contaminants can clog the nozzle and change the spray pattern, so clean or replace it if the flow drops. If you don't have the system itself yet, you can start with a complete water methanol kit or browse the entire water methanol injection category.

Frequently asked questions

Can I switch to a larger nozzle without changing anything else?

It depends on the system. A larger nozzle increases the flow, so the controller settings typically need to be adjusted, and the pump must be able to deliver sufficient pressure. Adjust gradually and keep an eye on how the engine responds.

Which nozzle holder should I choose?

Choose according to hose type and available space. Holders with push-to-connect fittings suit 1/4-inch tubing, while 4AN variants suit AN hoses. A 90-degree or low-profile holder can be an advantage where space at the intake is tight.

How can I tell if a nozzle is clogged?

Typical signs are an uneven or weak spray pattern and lower flow. Remove the nozzle and check the spray pattern in a test without the engine running. Clean or replace the nozzle if the pattern is not even.

View as Grid List
Sort by
Display per page

Nozzle Holder - SNO-809-BRD

snoSNO-809-BRD
Snow Performance 1/8in. NPT Female to 4AN Male Low Profile Water Nozzle Holder 4AN Elbow
$225.83 excl. VAT

Nozzle Holder - SNO-809-QC

snoSNO-809-QC
Snow Performance 90 Degree Nozzle Holder (1/8in. NPT to 1/4in. OD Tube) - Black
$225.90 excl. VAT

Nozzle Holder - SNO-810-QC

snoSNO-810-QC
Snow Performance 1/8in NPT to 1/4in Quick-Connect Low Profile Straight Nozzle Holder
$225.76 excl. VAT

Nozzle Holder - SNO-901

snoSNO-901
Snow Performance 90 Degree Water Nozzle Holder
$136.92 excl. VAT

Water-Meth Nozzle - SNO-N0050

snoSNO-N0050
Snow Performance Water Methanol Injection Nozzle 0.5GPH
$317.35 excl. VAT

Water-Meth Nozzle - SNO-N0075

snoSNO-N0075
Snow Performance Water Methanol Injection Nozzle 0.75GPH
$317.29 excl. VAT