0

O-rings

Is coolant seeping from the thermostat housing, or does an AN fitting in the fuel system need to seal again? An O-ring is a small rubber ring that seals between two parts. Here you can choose between individual O-rings and complete kits for the engine, fuel system and front fork, both for repairs and for your project.

What O-rings seal – from thermostat to AN fittings

An O-ring sits in a groove and is compressed when the parts are assembled, sealing against coolant, oil, fuel or air. The range includes, for example, thermostat O-rings and an O-ring kit for fuel injectors from MAHLE Original, a throttle body O-ring from FAST and O-rings for AN fittings from Fragola and Radium Engineering. There are also O-rings for the front fork compression piston from KYB and a diaphragm and O-ring kit for fuel pressure regulators from Fuelab. Individual parts are found under O-rings, while O-ring kits combine several sizes or all the rings for one component.

How to choose the right O-ring

Several factors must match before the ring seals reliably:

  • Size: Inner diameter and cross-section must match the groove. A ring that is too thin can leak, and one that is too thick can get pinched.
  • Material: NBR (nitrile rubber) is typically used for oil and fuel, but suitability depends on the fluid and temperature.
  • Hardness: Specified in Shore, e.g. 70 for Athena's NBR O-ring. The choice depends on pressure and the surface finish.
  • Fitting type: For AN fittings, the ring must match both the AN size and the thread, e.g. -8AN with 3/4-16.

Installation and maintenance

Clean the groove and the contact surface, and lightly lubricate the O-ring with a product compatible with the material and the fluid so it doesn't twist or get cut during assembly. Guide it carefully past sharp edges and threads. If you also need to replace gaskets, you can find them under engine gaskets and seals and in the rest of gaskets and seals. Brands in the category include, for example, Victor Reinz, Fel-Pro, Cometic Gasket, S&S Cycle and Athena.

Frequently asked questions

Can I reuse an O-ring?

It is typically not recommended. After use, the ring is often flattened and can be hardened or cracked by heat and fluids, so it seals less effectively. Replace it every time the joint is taken apart.

Should I choose individual O-rings or an O-ring kit?

Individual O-rings are a good fit when you know the exact size. A kit is practical for e.g. fuel injectors or a fuel pressure regulator, where several rings are replaced at the same time, or when your project has several AN sizes.

Why does a new O-ring leak?

Typical causes are the wrong size, a material that doesn't tolerate the fluid, a ring that was twisted or cut during installation, or a scratched or dirty groove. Check the size and material for the specific part number.

How do I measure an O-ring?

Measure the inner diameter and the cross-section with a caliper. A used ring may be stretched or flattened, so compare with the groove dimensions or the manufacturer's dimensions for the component the ring sits in.

View as Grid List
Sort by
Display per page

Fuel Inj O-ring Set

felES72761
Fel-Pro GMC Acadia ES 72761 Fuel Injector O-Ring Kit
142,37 € excl. VAT

Fuel Inj O-ring Set

felES731191
Fel-Pro Ford F-150 ES 73119-1 Fuel Injector O-Ring Kit
834,70 € excl. VAT

FUELAB Diaphragm Kit

flb14604
Fuelab Diaphragm & O-Ring Kit for 555xx Series Regulators
260,78 € excl. VAT

Gasket

pfs08-0113
Peterson Fluid Systems O-Ring For 7in Diameter Oil Tank
98,22 € excl. VAT

Gasket - 11661

nex11661
Nitrous Express Gasket for Part Number 11660/11661
141,64 € excl. VAT

GM Gen-3/4 LS Fuel Injector O-Ring Kit

cgsC15027
Cometic GM Gen-3/Gen-4 Small Block V8 LS Fuel Injector O-Ring Kit - Upper and Lower O-Rings
263,28 € excl. VAT

GM Gen-3/4 SB V8 Water Pump O-Ring

cgsC15033
Cometic GM Gen-3/4 Small Block V8 .031in Fiber Water Backing O-Ring
54,43 € excl. VAT

Granatelli Exhaust Clamp

gms318530R
Granatelli O-Ring Replacement for 3.0in Dual Seal Clamp
92,13 € excl. VAT

Granatelli Exhaust Clamp

gms318540R
Granatelli O-Ring Replacement for 4.0in Dual Seal Clamp
111,05 € excl. VAT

Granatelli Exhaust Clamp

gms318535R
Granatelli O-Ring Replacement for 3.5in Dual Seal Clamp
100,41 € excl. VAT

High Pressure O-Ring

felES73063
Fel-Pro Ford F-250 Super Duty ES 73063 Engine Oil Pump High Pressure O-Ring Kit
100,41 € excl. VAT

Hond B Series Water Pump Mounting O-Ring

cgsC4677
Cometic Honda B16A2/B18A1/B18B1/B18C1/B18C5/B20B4/B20Z2 Water Pump O-Ring
60,57 € excl. VAT

Honda D15/D16 Water Pump O-Ring

cgsC4700
Cometic Honda D15B1/D15B2/D15B7/D16A6/D16A7 Water Pump O-Ring
72,37 € excl. VAT

Honda D16B Water Pump O-Ring

cgsC4662
Cometic Honda D16B5/D16Y5/D16Y7/D16Y8 Water Pump O-Ring
80,94 € excl. VAT

Lines & Fittings

dwk6-02-0307
DeatschWerks ORB -6 Viton O-Ring (Pack of 10)
122,66 € excl. VAT

Lines & Fittings

dwk6-02-0310
DeatschWerks ORB -12 Viton O-Ring (Pack of 10)
122,66 € excl. VAT

Lines & Fittings

dwk6-02-0306
DeatschWerks ORB -4 Viton O-Ring (Pack of 10)
122,66 € excl. VAT

MAHLE Original 1 O-Ring

vic72006
MAHLE Original 1 O-Ring
43,69 € excl. VAT

MAHLE Original 1 X 1 3 O-Ring

vic72120
MAHLE Original 1 X 1 3 O-Ring
41,01 € excl. VAT

MAHLE Original 1.1 O-Ring

vic72124
MAHLE Original 1.1 O-Ring
40,78 € excl. VAT

MAHLE Original 1.1 O-Ring

vic72128
MAHLE Original 1.1 O-Ring
41,01 € excl. VAT