0

Forged Pistons

How much boost and how many revs does the engine need to handle for your project? Forged pistons are formed from pressed aluminium and can typically withstand higher pressure and heat than cast pistons. This category includes both complete sets and single pistons in several bore sizes and compression ratios.

What forged pistons do in the engine

A forged piston has a denser material structure than a cast one and can therefore typically better withstand the stress from high boost, nitrous or high revs. On the other hand, forged aluminium often expands more with heat, so greater clearance to the cylinder wall is required. If the engine runs moderate power, cast pistons can be an alternative – you'll find both types among our pistons.

How to choose forged pistons

The choice depends on more factors than the power target alone:

  • Bore and oversize: Measure the cylinders before you order. Some pistons are available in standard size as well as e.g. +.020in and +.030in.
  • Dish volume and compression: A deeper dish lowers compression. For example, Wiseco pistons for the same engine type are available with both -14cc and -21cc.
  • Stroke: Stroker pistons are designed for a specific stroke, e.g. CP Pistons for the Ford 5.0L with 3.750in stroke and 3.572in bore.
  • Set or single piston: Some items are sold individually, e.g. a piston from JE Pistons with CR 8.5 for the right side.

Installation and break-in

The cylinders should be measured and typically honed to the clearance the manufacturer specifies for that exact piston. Also check ring gaps, wrist pins and connecting rods before assembling the engine. Forged pistons can make slightly more noise on cold start due to the larger clearance, and the manufacturer's break-in instructions should be followed.

Frequently asked questions

What is the difference between forged and cast pistons?

Forged pistons typically have a stronger material structure and withstand more pressure and heat, but often require greater clearance to the cylinder wall. Cast pistons can be sufficient if the engine runs moderate power.

Does the engine block need machining when I switch to forged pistons?

It depends on the condition of the block and the piston dimensions. The cylinders should always be measured, and they often need to be honed or bored to the clearance and oversize the manufacturer specifies for the specific part number.

What does the cc figure in the product name mean, e.g. -21cc?

The figure typically indicates the volume in the piston crown. A minus usually means a dish that increases the combustion chamber volume and lowers compression. The actual compression also depends on the cylinder head, gasket and stroke.

View as Grid List
Sort by
Display per page

JE Pistons, Piston

jep321249R
JE Pistons Nissan VQ35DE 95.5mm Bore -12.6cc Dish - Single Right Side Piston
2.151,36 € excl. VAT

JE Pistons, Piston

jep337966S
JE Pistons Audi TT RS 82.5mm Bore - Single
2.208,16 € excl. VAT

JE Pistons, Piston

jep345633S
JE Pistons BMW S50B32 Euro Kit 87mm Bore -5.2cc Dome 0.827in Pin Diameter - Single Piston
2.313,01 € excl. VAT

JE Pistons, Piston

jep291059L
JE Pistons SUB STI EJ257 Block w/ EJ20 Head 99.5mm Bore CR 8.5 (Left Side) Single Piston
2.146,50 € excl. VAT

JE Pistons, Piston

jep373699R
JE Pistons Chevy Small Block 4.030in Bore -3.8cc (Right Side) - Single Piston
1.248,13 € excl. VAT

JE Pistons, Piston

jep321239L
JE Pistons GM LS1 3.898 in. Bore - 1.340 CD -2cc - Flat Top - Single Piston
1.237,30 € excl. VAT