0

Gaskets & Seals

Is your engine sweating oil at a joint, or does the cylinder head need to come off during a project? Gaskets and seals keep oil, coolant, combustion gases and compression where they belong between the parts of the engine, exhaust and drivetrain. The category covers everything from oil seals and O-rings to complete gasket kits and gasket material for both daily drivers and tuned projects.

What gaskets and seals do

A gasket fills the small irregularities between two surfaces so the joint stays sealed under pressure and heat. Among engine gaskets and seals you will find, for example, head gaskets, intake manifold gasket kits, oil filter housing gaskets and timing belt cover seals. Rotating shafts are typically sealed with oil seals, while O-rings are used in fittings and housings, for example. For the drivetrain there are separate groups for gearbox, differential and transfer case.

How to choose the right gasket

Start with the engine code or the part number of the original part – fitment depends on engine and model year, not just the car model. Then consider:

  • Thickness: A head gasket affects the compression ratio, so the thickness should be chosen based on the engine build and any decking or resurfacing of the cylinder head or block.
  • Bore: With larger pistons, the gasket bore must match the new cylinder diameter, e.g. 83.5 mm on a Cometic head gasket for the Audi 2.5 TFSI.
  • Material: Multi-layer steel (MLS) gaskets can typically handle higher cylinder pressure and boost than soft gaskets, but often require flat surfaces with the correct surface finish.
  • Single part or kit: If several joints need to be opened, a complete kit, such as the Fel-Pro intake manifold kits for the Ford Mustang and Dodge Challenger, can ensure you are not missing a single gasket.

Exhaust, installation and gasket material

Exhaust gaskets sit at the exhaust manifold, headers and flange joints, where heat and vibration put them under heavy stress. New headers may require different gaskets than the originals, so check the flange shape. When installing: clean the surfaces thoroughly, check them for warping, and tighten to the manufacturer's torque and sequence. If no ready-made gasket is available, you can cut your own from gasket material sheets, e.g. for covers and low-pressure flanges.

Brands and engines in the category

Brands include Cometic Gasket, Fel-Pro, Victor Reinz, Vertex Pistons and Wiseco. The range includes parts for engines such as the Ford 302/351W and 4.6/5.4L V8, Nissan RB20/RB26DETT and Audi 2.5 TFSI, as well as a few motorcycle and ATV engines such as the Yamaha YFZ450R.

Frequently asked questions

Can I reuse an old gasket?

It is generally not recommended. A gasket is compressed and conforms to the surfaces on first installation, so it rarely seals as well a second time. This applies especially to head and exhaust gaskets, where pressure and heat are highest.

How do I choose the thickness of a head gasket?

The thickness affects the compression ratio and the clearance between piston and cylinder head. If the head or block has been resurfaced, or different pistons have been fitted, the thickness should be calculated from the actual measurements rather than just the original spec.

Should I use gasket sealant with a new gasket?

It depends on the gasket and the manufacturer's instructions. Many multi-layer steel and coated gaskets should be installed dry, while certain joints, e.g. where two parts meet at a corner, may require a small amount of sealant.

Why is a new gasket leaking?

Typical causes are warped or dirty surfaces, incorrect torque or tightening sequence, reused bolts or a gasket that does not fit the specific engine. Check the surfaces and the engine code before you install a new one.

Gaskets & Seals
View as Grid List
Sort by
Display per page

BMC 1275 A/A+ Series Cylinder Head

cgsC14046-030
Cometic BMC 1275 A Series/A+ Series .030in MLS Cylinder Head Gasket - 72mm Bore
833,73 € excl. VAT

BMC 1500/1600/1600 Mark II Cylinder Head

cgsC4359-051
Cometic BMC 1500/1600/1600 Mark II B Series .051in MLS Cylinder Head Gasket - 74mm Bore
838,16 € excl. VAT

BMC 1500/1600/1600 Mark II Cylinder Head

cgsC4359-036
Cometic BMC 1500/1600/1600 Mark II B Series .036in MLS Cylinder Head Gasket - 74mm Bore
836,22 € excl. VAT

BMC 1500/1600/1600 Mark II Cylinder Head

cgsC4359-030
Cometic BMC 1500/1600/1600 Mark II B Series .030in MLS Cylinder Head Gasket - 74mm Bore
836,04 € excl. VAT

BMC 1500/1600/1600 Mark II Cylinder Head

cgsC4359-040
Cometic BMC 1500/1600/1600 Mark II B Series .040in MLS Cylinder Head Gasket - 74mm Bore
836,22 € excl. VAT

BMC 948/1098 A Series Cylinder Head Gask

cgsC4145-043
Cometic BMC 948/1098 A Series .043in Copper Cylinder Head Gasket 67.5mm Bore
754,67 € excl. VAT

BMC 948/1098 A Series Cylinder Head Gask

cgsC4145-063
Cometic BMC 948/1098 A Series .063in Copper Cylinder Head Gasket - 67.5mm Bore
749,32 € excl. VAT

BMC 948/1098 A Series Cylinder Head Gask

cgsC4145-080
Cometic BMC 948/1098 A Series .080in Copper Cylinder Head Gasket - 67.5mm Bore
751,32 € excl. VAT

BMC 948/1098 A Series Cylinder Head Gask

cgsC4145-050
Cometic BMC 948/1098 A Series .050in Copper Cylinder Head Gasket - 67.5mm Bore
749,19 € excl. VAT

BMC 948/1098 A Series Cylinder Head Gask

cgsC4145-032
Cometic BMC 948/1098 A Series .032in Copper Cylinder Head Gasket - 67.5mm Bore
747,31 € excl. VAT

BMW 14-19 B46/B48 Cylinder Head Gasket

cgsC14185-032
Cometic Gasket BMW 2014-2019 B46/B48 .032in MLX Cylinder Head Gasket - 83.5mm Bore
835,85 € excl. VAT

BMW 20+ S58B30T0 Cylinder Head Gasket

cgsC15696-055
Cometic 2020+ BMW S58B30T0 .055in MLX Cylinder Head Gasket - 85mm Bore
1.517,05 € excl. VAT

BMW 20+ S58B30T0 Cylinder Head Gasket

cgsC15696-036
Cometic BMW 2020+ S58B30T0 .036in MLX Cylinder Head Gasket - 85mm Bore
1.418,11 € excl. VAT