0

Fittings & Hoses

Which AN size, hose type and fitting does your next fuel or oil project need? In this category we bring together hoses, lines, fittings, plugs, hose clamps, brackets, valves and complete fuel kits. The parts are for you if you are building new lines, relocating components or want leak-free connections that can handle pressure, heat and vibration in the engine bay.

How the plumbing system fits together

A line system for fuel, oil, coolant or vacuum typically consists of three parts: the hose or hard line itself, the fittings and plugs that connect the line to the pump, filter or carburettor, and the clamps and brackets that hold it in place. Check valves control the direction of flow, while shut-off valves close off a line. If you don't want to build everything from scratch, there are complete fuel system kits, e.g. DeatschWerks 6AN PTFE Fuel Line Kit for 4160-style carburettors with pressure gauge.

How to choose hoses and fittings

Start with the fluid, the pressure and the temperature. PTFE hoses are typically used for fuel, but whether a hose suits your fuel depends on the manufacturer's specification for that particular hose. Then choose the size based on the engine's flow requirements and the space you have for routing – a larger size is not automatically better.

  • AN size: e.g. 6AN, 8AN or 10AN must match the hose, the fittings and the component ports.
  • Thread type: AN, NPT, ORB and SAE seal in different ways and require an adapter to connect, e.g. Radium Engineering 10AN ORB to 6AN Male Fitting or DeatschWerks 8AN Long to 7/8-20 Carb Adapter for the carburettor inlet.
  • Angle and design: 90-degree fittings and swivel banjo fittings can shorten line runs and make installation easier in tight spaces.
  • Material and finish: must suit the fluid, the temperature and the rest of the system.

Installation and safe routing

Route the lines away from the exhaust manifold, moving parts and sharp edges, and secure them so vibration doesn't wear the hose. For this you use hose clamps and brackets, e.g. Russell Line Clamp, while protective sleeving such as Convoluted Tubing can shield against chafing. Follow the manufacturer's instructions when assembling fittings onto the hose, and pressure test the system before starting the engine. Check the connections after the first drives and then regularly for moisture, cracks and loose clamps. In this category you will find brands such as Gates, Fragola, DFC, Russell and Vibrant.

Frequently asked questions

Can I mix AN, NPT and ORB fittings?

Not directly. The thread types are different and each seals in its own way. You need an adapter with the correct type at both ends, and you should check that the sizes match both the hose and the component.

Which hose should I use for fuel?

It depends on the fuel type, pressure and temperature. PTFE hoses are typically used for fuel, but always check the manufacturer's specification for the specific hose, especially if you run ethanol-blended fuel.

How do I find the right AN size?

Look at the engine's fuel requirements, the pump and filter ports and the manufacturer's recommendation. Hose, fittings and components must match throughout the whole system; a larger size does not automatically give a better result.

Can I modify the fuel lines on a road car?

It depends on the product and the car. Check the inspection requirements and any approval for the specific part number, and make sure the lines are properly secured and routed safely away from heat and moving parts.

Fittings & Hoses
View as Grid List
Sort by
Display per page

MILD STEEL FITTING

vib11283
Vibrant 5/8in ID Hose Barbed Weld Bung - Mild Steel
83,38 € excl. VAT

Mishimoto MMBB-STBK

misMMBB-STBK
Mishimoto M20 x 5/8 Straight Black Banjo Fitting w/ Bolt
366,84 € excl. VAT

Mishimoto MMBK-F2D-08HL

misMMBK-F2D-08HL
Mishimoto 08-10 Ford 6.4L Powerstroke Factory Fit Boot - Hot Side Lower Boot
965,45 € excl. VAT

Mishimoto MMBK-F2D-08HU

misMMBK-F2D-08HU
Mishimoto 08-10 Ford 6.4L Powerstroke Factory Fit Boot - Hot Side Upper Boot
535,61 € excl. VAT

Mishimoto MMBK-RAM-19

misMMBK-RAM-19
Mishimoto 2019+ RAM Cummins 6.7L Factory-Fit Boot Kit
2.370,85 € excl. VAT

Mishimoto MMCLAMP-15

misMMCLAMP-15
Mishimoto 1.5 Inch Stainless Steel T-Bolt Clamps
104,30 € excl. VAT

Mishimoto MMCLAMP-325T

misMMCLAMP-325T
Mishimoto 3.25 Inch Stainless Steel Constant Tension T-Bolt Clamp
137,81 € excl. VAT

Mishimoto MMCLAMP-35

misMMCLAMP-35
Mishimoto 3.5 Inch Stainless Steel T-Bolt Clamps
104,72 € excl. VAT

Mishimoto MMCLAMP-375T

misMMCLAMP-375T
Mishimoto 3.75 Inch Stainless Steel Constant Tension T-Bolt Clamp
137,87 € excl. VAT

Mishimoto MMCLAMP-375TGD

misMMCLAMP-375TGD
Mishimoto 3.75 Inch Stainless Steel Constant Tension T-Bolt Clamp - Gold
183,24 € excl. VAT

Mishimoto MMCLAMP-3GD

misMMCLAMP-3GD
Mishimoto 3 Inch Stainless Steel T-Bolt Clamps - Gold
129,23 € excl. VAT

Mishimoto MMCLAMP-3TGD

misMMCLAMP-3TGD
Mishimoto 3 Inch Stainless Steel Constant Tension T-Bolt Clamp - Gold
187,92 € excl. VAT

Mishimoto MMCLAMP-4

misMMCLAMP-4
Mishimoto 4 Inch Stainless Steel T-Bolt Clamps
104,91 € excl. VAT

Mishimoto MMCLAMP-425T

misMMCLAMP-425T
Mishimoto Stainless Steel Constant Tension T-Bolt Clamp 4.09in.-4.41in. (104mm-112mm)
138,84 € excl. VAT

Mishimoto MMCLAMP-CTWG-54

misMMCLAMP-CTWG-54
Mishimoto Constant Tension Worm Gear Clamp 1.26in.-2.13in. (32mm-54mm)
97,43 € excl. VAT

Mishimoto MMCLAMP-WG-27HT

misMMCLAMP-WG-27HT
Mishimoto High-Torque Worm Gear Clamp 0.55in.-0.1.06in. (14mm-27mm) - Pack of 10
105,33 € excl. VAT

Mishimoto MMCLAMP-WG-27HTGD

misMMCLAMP-WG-27HTGD
Mishimoto High-Torque Worm Gear Clamp 0.55in.-0.1.06in. (14mm-27mm) - Pack of 10 - Gold
137,62 € excl. VAT

Mishimoto MMCLAMP-WG-32HT

misMMCLAMP-WG-32HT
Mishimoto High-Torque Worm Gear Clamp 0.71in.-0.1.26in. (18mm-32mm) - Pack of 10
108,31 € excl. VAT

Mishimoto MMCLAMP-WG-32HTBK

misMMCLAMP-WG-32HTBK
Mishimoto High-Torque Worm Gear Clamp 0.71in.-0.1.26in. (18mm-32mm) - Pack of 10 (Black)
149,49 € excl. VAT

Mishimoto MMCLAMP-WG-44HTBK

misMMCLAMP-WG-44HTBK
Mishimoto High-Torque Worm Gear Clamp 0.83in.-1.73in. (21mm-44mm) - Pack of 10 (Black)
160,98 € excl. VAT

Mishimoto MMCLAMP-WG-51HTBK

misMMCLAMP-WG-51HTBK
Mishimoto High-Torque Worm Gear Clamp 1.06in.-2.01in. (27mm-51mm) - Pack of 10 (Black)
147,73 € excl. VAT

Mishimoto MMCLAMP-WG-64HTBK

misMMCLAMP-WG-64HTBK
Mishimoto High-Torque Worm Gear Clamp1.57in.-2.52in. (40mm-64mm) - Pack of 10 (Black)
152,16 € excl. VAT

Mishimoto MMCLAMP-WGP-120

misMMCLAMP-WGP-120
Mishimoto Sure Grip Worm Gear Clamp 120mm - Pack of 2
129,54 € excl. VAT

Mishimoto MMCLAMP-WGP-56

misMMCLAMP-WGP-56
Mishimoto Sure Grip Worm Gear Clamp 56mm 10-Pack
245,03 € excl. VAT